DIY Ferrofluid display bottle audio visualizer kits music sound speaker mate

Description: Note before buying:You must read this page before creating a DIY creation.You must have some hands-on skills as well as knowledge of electronics.The kit uses 5V input, The visualiser supports 5-24V voltage. A solution for audio visualizers that can dance to music.Working principle: It controls the change of magnetic field by Capture sound to make the ferrofluid dance.Video Demo: https://youtu.be/RY1i4QbJ8qE?si=oOjuf6Rchl_rrdQ0 Note: this kit does not include the ferrofluid display bottle.About ElectromagnetsModelmagnetic forcevoltagecurrentpowermounting holeP34/1820kg5V0.3A1.5WM4P40/2030kg5V0.6A3WM5P49/2145kg5V0.6A3WM6 Electromagnet with Ferrofluidic Display Bottle AdaptationModelMagnetic forceFerrofluidContainer (Red is the preferred ratio)P34/1820kg1-2ml15mlP40/2030kg3-4ml50mlP49/2145kg5-6ml50-100ml note:The pairing of a ferrofluid with an electromagnet does not absolutely depend on the magnetic force of the electromagnet.Another important factor is the size of the magnetic surface of the electromagnet.The larger the magnetic surface, the shorter the travel between the electromagnet and the ferrofluid, and the easier it is for the ferrofluid to be sucked up.Therefore, when you purchase a ferrofluid that is not the size we recommend, please consider the distance between the electromagnet and the ferrofluid.About Container (Bottle)About visualiser Shell dismantling and wire strippingIntroduction of visualiser the main function of the visualiser is voice-controlled, by capturing the sound to control the electromagnet to drive the ferrofluid to dance. The visualiser defaults to on-board voice control mode when it is turned on. This mode, it can be set to power on as soon as power is supplied, thus doing away with the presence of the on-board switch button. It can work without connecting the mobile phone.Support connecting mobile phone via Bluetooth to use proprietary APP. Static Dynamic: slow jump, fast, medium speed, cycle Music: ☞On-board built-in microphone that moves with the sound; ☞mobile phone microphone, moving with the sound; ☞Play music streaming within APP.Support APP to adjust the sensitivity / intensity.Support APP as well as firmware upgrade.parametersWorking Voltage: DC5V~ 24VWorking Current: 10mA~ 22mAPWM Single Channel Maximun Output Current 2AWorking Temp: -20 ° C~ 60 ° CSize: ☞With shell, 55 * 26 * 12; ☞NO shell: 42 * 20 * 4; ☞not including the wires.For specific technical support please visit ——Visualiser Manual: https://kdocs.cn/l/cdx4SPpOM2ex ——APP Demo: https://youtu.be/RGkmivAHEDQ?si=WILeMIWD64U23S2SAbout Power Supply Power port: DC cable and Type-C cable.Voltage: input 5V, 2A Please note that if you choose a USB cable, you don't need Type-C cable, just choose one of the two.You only need to plug it in directly with your own 5 V mobile phone power adapter.It is recommended that you use the original power adapter of your phone.Packing DescriptionKits contains : ——only Visualizer ☞☞(Include : Type-c Port + DC Port + Quick Connect Port, etc., accessories) ——visualizer + Electromagnet ☞☞(Include : Type-c Port (USB to DC cable) + DC Port + Quick Connect Port, etc., accessories) ****The picture below is just for show, it does not contain a ferrofluid display bottle. Problem AnalysisQuestion about electromagnets and ferrofluid combinations:Electromagnets produced by different manufacturers in the quality standard difference is not large, they may be slightly different in the labeling of the magnetic force, such as P34/18 will be labeled as 20kg/18kg/15kg, this situation can be ignored only need to look at the model.Introduction of bottles、 ① 15ml rectangular bottle, with screw top can be opened, usually for beginners to start using; ② 50ml rectangular bottle, can not be screwed; ③ 50ml square bottle, can not be screwed; ④ 50ml round bottle, with screw top can be opened; ⑤ 100ml round bottle, can not be screwed, the most widely used. If you have other needs you can let us know.Demonstration videos of application scenarios for several of electromagnets, ferrofluids, and bottles. Please visit this link: https://www.youtube.com/@4dbottle/videosAll kinds of difficult casesvisualiser with how much voltage. 5V-24V wide voltage, input is 5V, output that is 5V, input 12V output that is 12V, can't be lower than 5V and higher than 24V. How much voltage do you use for the kit? 5V voltage has been configured for you, directly with your mobile phone charger can be (recommended to use the original). Can I use 12V? Yes most of the electromagnet, light strip and other accessories regular voltage is 12V, 5V will be much more expensive. Note that if you have your own solenoid, then you want to go with the input voltage of the solenoid. That is, if the solenoid is 5V, then your input voltage is going to be 5V. If I choose TP-C interface, do I still need DC interface? No, according to your needs, just choose one of the two. What's a DC one-two cable for? The bus is divided into two ways, one way to connect the visualiser, one way to connect the lamp to the ferrofluid display bottle lighting. You can also be used to do double cylinder one tow two, each way to a visualiser. the light belt using positive white light, 5CM long, enough for lighting. if you need colourful light bands to follow the music rhythm, you can buy a set of LED colour light controller. the magnetic fluid body jumps abnormally, no energy. Try to connect the mobile phone APP to see if the mode is the on-board microphone status in music mode; try to replace the power adapter, it is more demanding on the power adapter, if this situation shows that the power is not enough. The kit is too big to fit in the box. The visualiser housing is too large and can be removed; If you feel that the wiring as well as the DC connectors are too big, you can choose to strip the wires and use quick connectors for the wiring. How much kg electromagnet can the visualiser drive? This needs to be determined according to your power input, the visualiser has a maximum output of 2A, assuming that your power supply is 1A, then the output is 1A, 240kg electromagnet is only about 0.5A, so don't worry about the power of the electromagnet. The kit is an inductive load, so generally we need to input 1-2A current to ensure normal operation under instantaneous voltage current. If the power adapter is underpowered, the ferrofluidic body will feel powerless or not work at all. The lighting will flicker along with it. Do I need to connect the Bluetooth to work with the visualiser? Please see the first half of the content, the content is very clearly expressed, the visualiser does not need Bluetooth to work. Which power adapter should be used for 5V, 12V, 24V? If you are a novice or don't know anything about electricity, you simply ignore it and remember to use your mobile phone's power adapter directly.Service DescriptionIf you have any questions please send me a message and I will address any queries you may have.Finally, I may not have used the right words in the description of my information, so if anyone doesn't understand something, please come and ask me as well as point out the mistakes to me, thank you very much.

Price: 9.9 USD

Location: FuJian

End Time: 2024-11-30T15:14:29.000Z

Shipping Cost: 8 USD